Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: Glassing Advice Please

Glassing Advice Please 11 years 2 months ago #84506

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
Hello again to all. I'm getting ready to do the final glass-in of the floor on my '60 G3. I'd appreciate some advice before I do anything that would screw it up. My question is if it's necessary to take the mat up the gunnels/transom and, if so, how far?

I've attached a photo of the transom so you can see what I've done so far. I can't figure out how to attach multiple photos so I'll attach a sponson shot to a separate message. Here's some technical info that my help answer my question. The transom is three plys of 1/2" Meranti laminated with one layer of random strand mat using polyester resin. I was able to preserve the exterior skin of the transom and the transom laminate is laminated to it with a layer of mat/resin. I finished the installation with a final layer of mat/resin over the interior surface but didn't wrap the sides and only wrapped the floor/transom joint about an inch. The sponson covers are a single ply of 1/4" Meranti covered with a layer of mat/resin front and back prior to glassing in. The covers are secured in place with resin thickened with carbosil. the seams where the transom meets the sponsons and the floor are filleted with the same carbosil/resin.

I think that's everything. Thanks in advance for your help.

D
Attachments:

Please Log in or Create an account to join the conversation.

Re:Glassing Advice Sponson Pic 11 years 2 months ago #84507

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
Here's the sponson shot.
Attachments:

Please Log in or Create an account to join the conversation.

Re:Glassing Advice Sponson Pic 11 years 2 months ago #84512

  • morris
  • morris's Avatar
  • Offline
  • Expert Boarder
  • Expert Boarder
  • Posts: 393
  • Karma: 38
  • Thank you received: 0
It's looking very good Doug,
Looks likes time for the fiberglass cloth and paint. Super looking job.

Please Log in or Create an account to join the conversation.

Glasspar g-3 Owners Club, Marque Club Representative ACBS
www.g3owners.com

Re:Glassing Advice Sponson Pic 11 years 2 months ago #84630

where are the stringers?

Please Log in or Create an account to join the conversation.

Re:Glassing Advice Sponson Pic 11 years 2 months ago #84663

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
I'm not using traditional stringers because my woodworking skills weren't good enough to fit them properly. So, I used cross bracing with the braces tied together with 2 X 4 stock. I don't have a pic of the bracing with all of the 2 X 4's in place but the attached pic illustrates the idea.
Attachments:

Please Log in or Create an account to join the conversation.

Re:Glassing Advice Sponson Pic 11 years 2 months ago #84664

  • dspeck
  • Offline
  • Junior Boarder
  • Junior Boarder
  • Posts: 62
  • Karma: 4
  • Thank you received: 0
This pic shows a bit of the total 2 X 4 bracing.
Attachments:

Please Log in or Create an account to join the conversation.

Re:Glassing Advice Sponson Pic 11 years 2 months ago #84854

that looks very nice, might be a bit heaver than stock , but very strong.

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.186 seconds

Donate

Please consider supporting our efforts.

Glassified Ads

1956 Lonestar Meteor
( / Boats)

1956 Lonestar Meteor
12-24-2024

Mercury outboard
( / Engines)

noimage
11-03-2024

Classic Mercury Outboard Motors
( / Engines)

Classic Mercury Outboard Motors
10-18-2024

FG Login

FiberGoogle

Who's Online

We have 5630 guests and no members online