Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: convert to Pertronix Ignition?

convert to Pertronix Ignition? 4 years 5 months ago #142789

  • gdanderson
  • gdanderson's Avatar Topic Author
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 155
  • Karma: 33
  • Thank you received: 0
I would like to convert my 1963 short shaft Homelite to Pertronix ignition. Others may have done this already. Could anybody help me out with part numbers?

Greg Anderson
Monona, WI

PS: haven't been on this site for years. Getting revved up with my Homelites again!!

Please Log in or Create an account to join the conversation.

convert to Pertronix Ignition? 4 years 5 months ago #142796

  • Ike
  • Ike's Avatar
  • Offline
  • Expert Boarder
  • Expert Boarder
  • Posts: 480
  • Karma: 22
  • Thank you received: 14
Don't know about Homelite, but I did this on my Mercruiser 165 (basically a GM 250 6 cylinder inline) and it made a dramatic difference. Engine runs smoother, starts easier, and I only have to set the dwell. However, the only problem I ran into was with the coil. When I bought the ignition module, they recommended a specific coil. It did not work properly with my engine. When I re-installed the original coil it ran fine

Please Log in or Create an account to join the conversation.

Peter D. Eikenberry
newboatbuilders.com
"Don't tell me that I can't. tell me how I can."

convert to Pertronix Ignition? 4 years 5 months ago #142822

  • gdanderson
  • gdanderson's Avatar Topic Author
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 155
  • Karma: 33
  • Thank you received: 0
Got my answer from a very reliable source (Bill Roberts). Pertronix Part #1545. I have not installed yet but sure it will work.

Greg Anderson

Please Log in or Create an account to join the conversation.

convert to Pertronix Ignition? 4 years 4 months ago #142953

  • gdanderson
  • gdanderson's Avatar Topic Author
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 155
  • Karma: 33
  • Thank you received: 0
Got it installed and it works perfectly! Was all set to have to reset the timing. The motor started right up, idled smoothly as could be. Checked timing and it was perfect at 8* BTDC. Thank you Bill!

Greg Anderson
Monona, WI

Please Log in or Create an account to join the conversation.

convert to Pertronix Ignition? 4 years 4 months ago #142956

  • Ike
  • Ike's Avatar
  • Offline
  • Expert Boarder
  • Expert Boarder
  • Posts: 480
  • Karma: 22
  • Thank you received: 14
Bravo.

Please Log in or Create an account to join the conversation.

Peter D. Eikenberry
newboatbuilders.com
"Don't tell me that I can't. tell me how I can."

convert to Pertronix Ignition? 4 years 4 months ago #142976

  • billr
  • billr's Avatar
  • Offline
  • Moderator
  • Moderator
  • Posts: 621
  • Karma: 51
  • Thank you received: 0
Welcome.
Yes, I think the pertronix is a must have for these engines. Stable idle, instant starts, smooth cruise. Doesn't add power, just helps her start and run efficiently.
I sold all my factory tooling and parts.

Please Log in or Create an account to join the conversation.

convert to Pertronix Ignition? 4 years 3 months ago #143184

It does work well, but am curious if it requires a different coil?
Attachments:

Please Log in or Create an account to join the conversation.

convert to Pertronix Ignition? 4 years 3 months ago #143186

  • Ike
  • Ike's Avatar
  • Offline
  • Expert Boarder
  • Expert Boarder
  • Posts: 480
  • Karma: 22
  • Thank you received: 14

However, the only problem I ran into was with the coil. When I bought the ignition module, they recommended a specific coil. It did not work properly with my engine. When I re-installed the original coil it ran fine


As I said. they recommend a specific coil, but it didn't work right. If you do get a new coil make sure you can return it for a refund.

Please Log in or Create an account to join the conversation.

Peter D. Eikenberry
newboatbuilders.com
"Don't tell me that I can't. tell me how I can."

convert to Pertronix Ignition? 4 years 3 months ago #143188

  • Dr.Go!
  • Dr.Go!'s Avatar
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 1719
  • Karma: 19
  • Thank you received: 125
I have to comment that I love that boat and motor combo. I wish you the best at keeping it running and out on the water!

Please Log in or Create an account to join the conversation.

Dr.Go!

convert to Pertronix Ignition? 4 years 3 months ago #143190

  • gdanderson
  • gdanderson's Avatar Topic Author
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 155
  • Karma: 33
  • Thank you received: 0
I used the original coil that was installed on the motor when it was new in 1963. That coil has a rounded top and is about 5" +/- tall. To restate after instalation the motor started and ran great without having to retime.

Greg Anderson
Monona

Please Log in or Create an account to join the conversation.

convert to Pertronix Ignition? 4 years 3 months ago #143196

YUP.... it does.

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.185 seconds

Donate

Please consider supporting our efforts.

Glassified Ads

Mercury outboard
( / Engines)

noimage
11-03-2024

Classic Mercury Outboard Motors
( / Engines)

Classic Mercury Outboard Motors
10-18-2024

1958 Skagit Sportster
( / Boats)

1958 Skagit Sportster
09-25-2024

FG Login

FiberGoogle

Who's Online

We have 8773 guests and 2 members online