Welcome, Guest
Username: Password: Remember me
  • Page:
  • 1

TOPIC: 1960's Columbian Fury 8 foot

1960's Columbian Fury 8 foot 7 years 2 months ago #130017

1960's Columbian Fury made in CT. I found this on craigslist over a year ago and was part of a property clean out. He was more interested in selling me the John Deere tractor. The picture is how I found it. I have never restored anything like this so reading and learning has been the focus. Being small makes it easy. A redo is not a big deal. Some may question why I did things a certain way but its all part of learning. My goal is to restore to as original as I can get with a few up grades and have some fun. Toughest part will be outfitting the HEMI on the back.
Condition:
Mini transom rotted, mini stringers rotted, crack in bottom, holes punctured transom where motor mounts. Original seat vinyl cracked and rotted. I have to learn to fiberglass, sew, gel coat and everything in between
1960's 8 Foot Columbian Fury


I put the boat in my basement. Yup, right down the bulk head. Son helped for this. Sanded whole bottom with 220 grit and fixed this crack with some fiberglass matt and body filler for smoothness Inside the boat was backed with 1708 fiberglass. I used the West epoxy resin and catalyst. Stuff is a mess. Make sure your protected with mask, glasses and full body armor.

Gel coated bottom. Tip and Roll failed, too many deep lines to sand. I used small foam roller from Home Depot that worked the best. Smoother you get it on there the less sanding. I did four coats. I bought some thinner but too scared to mess it up so I did not use it. Looking back I think it would have made it even smoother. Spraying is the way to go ...but i had no sprayer.

Transom fully rotted. replaced with thicker 3/4" marine grade ply. Used two layers of 1708 fiberglass for layering and same resin system. I also did some smaller sections with a third layer. "Peanut Butter" paste resin for filling gaps and smoothing edges. Had to make it strong to hold the HEMI motor.



Controls were sanded down and sprayed with Rustoleum Enamel 3 coats primer, 3 base and three clear. For the handles I used automotive interior spray paint. This was for durability and ensuring it would adhere to plastic well. The red was also used to spray my rub rail. Rub rail was sanded with 400 grit then cleaned with Toluene. The toluene gets is nice and rubbery for paint adhesion. Came out real good. You may ask why spray paint. Well, replacing it would be a big undertaking and expense. This boat will not be used much.



The motor lid was sanded with a sanding dremmel tool. Paint stripper was not an option as i did not want it to eat the fiber glass.A heavy grit paper ate the old paint up, however be careful as the the heavy grit will leave some swirls. When painting it will magnify. Used automotive Rustoleum spray primer, white enamel and clear. Three coats of each. Automotive for the outdoor type toughness..I guess.


Finally have the boat out of the basement and in garage. The top of the boat is the original gel coat. I pressure washed it originally and used some ON-Off to eat some of dirt grime out. Then wet sanded. I used 220 then 400 to 600 to 1000 then compound buffer machine. If I did it again I would not use 220. Left scratches that were harder to get out than it should have been. I would start with 400 and use a couple of times then move on to the finer grit.
I also put on the red racing stripe. This is a transfer stripe that basically goes on in one piece. Make sure your surface is real clean as dirt makes tents and when its on its on. For curved surfaces like behind the seat it was easier to cut the stripe. So, I put the middle of the stripe on first. Then the two little ones on each side ensuring to measure the space. Trying in one piece, with the curve, will cause it to crease and is real tough to apply, even with a heat gun. Patience.

Finished seat and steering.....and added the HEMI

Please Log in or Create an account to join the conversation.

1960's Columbian Fury 8 foot 6 years 10 months ago #131629

WOW great work , that will be a fun boat to ride

Please Log in or Create an account to join the conversation.

1960's Columbian Fury 8 foot 6 years 10 months ago #131630

WOW great work , that will be a fun boat to ride

Please Log in or Create an account to join the conversation.

1960's Columbian Fury 8 foot 6 years 10 months ago #131633

  • Dr.Go!
  • Dr.Go!'s Avatar
  • Offline
  • Contributing Member
  • Contributing Member
  • Posts: 1719
  • Karma: 19
  • Thank you received: 125
Cool boat and nice job. Thanks for the pictures and information to go along with it! All info helps a bit more. That will be a blast AND a head turner.

Please Log in or Create an account to join the conversation.

Dr.Go!

1960's Columbian Fury 8 foot 6 years 10 months ago #131695

Appreciate the feedback! I will be posting some more updates soon. Closing in. I have blown this project out of proportion.

Please Log in or Create an account to join the conversation.

1960's Columbian Fury 8 foot 6 years 10 months ago #131698

Awesome!!!!!!!!!!!

Bob

Please Log in or Create an account to join the conversation.

1960's Columbian Fury 8 foot 6 years 9 months ago #132276

I would say this is pretty much done. Now I have to figure out what to do with it.

Please Log in or Create an account to join the conversation.

1960's Columbian Fury 8 foot 6 years 9 months ago #132282

Awesome! Sounds like you need one more, these are always more fun in pairs

Please Log in or Create an account to join the conversation.

1960 14' Speed Queen
1972 10' Tri-Cat 3
[Building] 10' Glen-L Squirt

1960's Columbian Fury 8 foot 4 years 10 months ago #139578

I thought I would never see another one of these. The only pictures I can find are my own.
Two years later I stumble across another one left behind. Owner had it for 20 years and was kept it in box truck.
Great guy. Not sure why I took it. My first one just sits there. Round two.
Attachments:

Please Log in or Create an account to join the conversation.

  • Page:
  • 1
Time to create page: 0.233 seconds

Donate

Please consider supporting our efforts.

FG Login

Glassified Ads

1975 16ft Cobalt
( / Boats)

1975 16ft Cobalt
03-27-2024

Homelie/Bearcat
( / Engines)

noimage
03-17-2024

Thunderbird Apache 1956 hardtop
( / Boats)

noimage
03-10-2024

FiberGoogle

Who's Online

We have 7340 guests and one member online