|
Welcome,
Guest
|
TOPIC: Sticky Control Cables
Sticky Control Cables 14 years 7 months ago #4877
|
I am restoring a couple motors; Mark 55 and a 58A.
I am having a hell of a time with the control cables. As with most of them, they have cracked and taped sections but no real kinks. They are 50+ years old and move like molasses. Has anyone had any luck taking the cables out of the housing, cleaning, lubing and re-assembling them? thanks for your time boys. T |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4878
|
I remove the inner cable then put a good amount of WD40 into the housing, then re-install the cable, then remove the cable using a rag to clean the cable as it is removed. Do this several times until free moving.
There has been a couple times that I have not been able to re-insert the cable after removal, I am sure that the casing was cracked or something and the cable gets bound in it and will not allow it back in. So at your own risk! Darrell |
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4882
|
the re-insertion part is my main worry. I guess it is worth it considering that they are just mush now.
thank you for your input. T |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4887
|
take the end off and hook a drill to it and spin before and during the removal part before reinsertion round off the end and lube with 105 lightly while reinserting.
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4961
|
And,...I have a pretty decent selection of used & some new replacement control cables if the need arrises.
Thom |
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4974
|
I just purchased those 2 Mark 55's on the classifieds, no controls.
I am interested in parts and maybe a whole system. lets talk. T |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4976
|
Thom I have had some luck with a piece of hose clamped over the cable end, fill with penetrating oil and use my air compressor to force the oil inside the cables
good luck |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #4977
|
great idea, would not have to take the cable out which could be a cluster...
thanks, see you Sunday. |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 7 months ago #5334
|
FYI - new cables are available and not terribly expensive. Remember, these, along with your steering cable, are your lifeline to your motor. If a cable breaks or sticks at speed, bad things can happen....
- Scott |
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 6 months ago #5957
|
I just purchase a set on EBay that were a dream, swear they came out of a boat that had been garaged for 40 years.
where can I get new/used cables boys? |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 6 months ago #6098
|
New cables as near as your local full service marina. Chances are, even if they're not a Merc dealer, they have access to the Teleflex catalog, which does include Mercury cables... Same cables are often used on MerCruiser stern drives, so they're available all over...
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 6 months ago #6100
|
Thom
the cables for the 2 lever controls, can be replaced with NEW OMC cables pre 1979 unscrew the OMC fittings and install your mercury ends the brass mercury barrells need to be drilled and re tapped to 1/4-20 threads |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 14 years 6 months ago #6125
|
thanks gents, I had no idea.
T |
|
|
Please Log in or Create an account to join the conversation. |
Re:Sticky Control Cables 13 years 8 months ago #26920
|
I just got around to tackling this task, seems I was a bit timid in the beginning as this project took me all of 45 minutes. I took Darrel's advice and took out the cable, sent a river of WD-40 down the housing and then reinserted the cable...repeat 3 times. it came out cleaner than a whistle and they move like a dream now.
thanks to Michael, Thom, Chinewalker and the other guys who gave the time and expertise. |
|
|
Please Log in or Create an account to join the conversation. |
Moderators: kensikora, classicfins, bruce gerard, billr, mrusson, cc1000, MarkS, Waterwings, jbcurt00
Time to create page: 0.198 seconds
Donate
Please consider supporting our efforts.
Glassified Ads
1967 23 ft powercat flybridge |
Mercury outboard( / Engines)
11-03-2024
Classic Mercury Outboard Motors( / Engines)
10-18-2024
FG Login
FiberGoogle
Who's Online
We have 4761 guests and 2 members online